This document was created by man2html using the manual pages.
Section: Maintenance Commands (8)
Updated: March 2002
Index Return to NetAdminTools
NAMEmke2fs - create a Linux second extended file system
SYNOPSISmke2fs [ -c | -l filename ] [ -b block-size ] [ -f fragment-size ] [ -i bytes-per-inode ] [ -j ] [ -J journal-options ] [ -N number-of-inodes ] [ -n ] [ -m reserved-blocks-percentage ] [ -o creator-os ] [ -O feature[,...] ] [ -q ] [ -r fs-revision-level ] [ -R raid-options ] [ -v ] [ -F ] [ -L volume-label ] [ -M last-mounted-directory ] [ -S ] [ -T filesystem-type ] [ -V ] device [ blocks-count ]
DESCRIPTIONmke2fs is used to create a Linux second extended file system on a device (usually a disk partition). device is the special file corresponding to the device (e.g /dev/hdXX). blocks-count is the number of blocks on the device. If omitted, mke2fs automagically figures the file system size. If called as mkfs.ext3 a journal is created as if the -j option was specified.
- -b block-size
- Specify the size of blocks in bytes. Valid block size vales are 1024, 2048 and 4096 bytes per block. If omitted, mke2fs block-size is determined by the file system size and the expected usage of the filesystem (see the -T option).
- Check the device for bad blocks before creating the file system. If this option is specified twice, then a slower, destructive, read-write test is used instead of a fast read-only test.
- -f fragment-size
- Specify the size of fragments in bytes.
- Force mke2fs to run, even if the specified device is not a block special device, or appears to be mounted.
- -i bytes-per-inode
- Specify the bytes/inode ratio. mke2fs creates an inode for every bytes-per-inode bytes of space on the disk. The larger the bytes-per-inode ratio, the fewer inodes will be created. This value generally shouldn't be smaller than the blocksize of the filesystem, since then too many inodes will be made. Be warned that is not possible to expand the number of inodes on a filesystem after it is created, so be careful deciding the correct value for this parameter.
- Create the filesystem with an ext3 journal. If the -J option is not specified, the default journal parameters will be used to create an appropriately sized journal (given the size of the filesystem) stored within the filesystem. Note that you must be using a kernel which has ext3 support in order to actually make use of the journal.
- -J journal-options
Create the ext3 journal using options specified on the command-line.
Journal options are comma
separated, and may take an argument using the equals ('=') sign.
The following journal options are supported:
- Create a journal stored in the filesystem of size journal-size megabytes. The size of the journal must be at least 1024 filesystem blocks (i.e., 1MB if using 1k blocks, 4MB if using 4k blocks, etc.) and may be no more than 102,400 filesystem blocks. The journal must fit within the newly created filesystem.
- Attach the filesystem to the journal block device located on external-journal. The external journal must already have been created using the command
- mke2fs -O journal_dev external-journal
- Note that external-journal must have been created with the same block size as the new filesystem.
- Instead of specifying a device name directly, external-journal can also be specified by either LABEL=label or UUID=UUID to locate the external journal by either the volume label or UUID stored in the ext2 superblock at the start of the journal. Use dumpe2fs(8) to display a journal device's volume label and UUID. See also the -L option of tune2fs(8).
- Only one of the size or device options can be given for a filesystem.
- -l filename
- Read the bad blocks list from filename. Note that the block numbers in the bad block list must be generated using the same block size as used by mke2fs. As a result, the -c option to mke2fs is a much simpler and less error-prone method of checking a disk for bad blocks before formatting it, as mke2fs will automatically pass the correct parameters to the badblocks program.
- Set the volume label for the filesystem.
- -m reserved-blocks-percentage
- Specify the percentage of the filesystem blocks reserved for the super-user. This value defaults to 5%.
- Set the last mounted directory for the filesystem. This might be useful for the sake of utilities that key off of the last mounted directory to determine where the filesytem should be mounted.
- causes mke2fs to not actually create a filesystem, but display what it would do if it were to create a filesystem.
- -N number-of-inodes
- overrides the default calculation of the number of inodes that should be reserved for the filesystem (which is based on the number of blocks and the bytes-per-inode ratio). This allows the user to specify the number of desired inodes directly.
- -o creator-os
- Manually override the default value of the "creator os" field of the filesystem. Normally the creator field is set by default to the native OS of the mke2fs executable.
- -O feature[,...]
Create filesystem with given features (filesystem options).
features are turned on by default unless
is run on a system with a pre-2.2 Linux kernel. Filesystems that
may need to mounted on pre-2.2 kernels should be created with
for 1.2 kernels) which will disable these features, even if
is run on a system which can support them.
The following filesystem options are supported:
- Create a filesystem with fewer superblock backup copies (saves space on large filesystems).
- Store file type information in directory entries.
- Create an ext3 journal (as if using the -j option).
- Create an external ext3 journal on the given device instead of a regular ext2 filesystem. Note that external-journal must be created with the same block size as the filesystems that will be using it.
- Quiet execution. Useful if mke2fs is run in a script.
- -r revision
- Set the filesystem revision for the new filesystem. Note that 1.2 kernels only support revision 0 filesystems. The default is to create revision 1 filesystems.
- -R raid-options
Set raid-related options for the filesystem. Raid options are comma
separated, and may take an argument using the equals ('=') sign. The
following options are supported:
- Configure the filesystem for a RAID array with stripe-size filesystem blocks per stripe.
- Write superblock and group descriptors only. This is useful if all of the superblock and backup superblocks are corrupted, and a last-ditch recovery method is desired. It causes mke2fs to reinitialize the superblock and group descriptors, while not touching the inode table and the block and inode bitmaps. The e2fsck program should be run immediately after this option is used, and there is no guarantee that any data will be salvageable. It is critical to specify the correct filesystem blocksize when using this option, or there is no chance of recovery.
- -T fs-type
Specify how the filesystem is going to be used, so that mke2fs can
chose optimal filesystem parameters for that use. The supported
filesystem types are:
- one inode per 4kb block
- one inode per megabyte
- one inode per 4 megabytes
- Verbose execution.
- Print the version number of mke2fs and exit.
AUTHORThis version of mke2fs has been written by Theodore Ts'o <email@example.com>.
BUGSmke2fs accepts the -f option but currently ignores it because the second extended file system does not support fragments yet.
There may be other ones. Please, report them to the author.
AVAILABILITYmke2fs is part of the e2fsprogs package and is available from http://e2fsprogs.sourceforge.net.
SEE ALSObadblocks(8), dumpe2fs(8), e2fsck(8), tune2fs(8)
Return to NetAdminTools,